TrySet Supply Voltage (V) to 3.3, LED Forward Voltage V_f (V) to 2.0 and Desired LED Current (mA) to 20. Then lower the desired current and watch the resistor choice.
ObserveThe opening voltage drop is 1.3 V, giving a calculated resistor of 65 ohms and a listed standard value of 68 ohms. Displayed resistor power is 26.0 mW.
ExplainSupply Voltage (V) minus LED Forward Voltage V_f (V) gives the resistor drop; dividing by Desired LED Current (mA), converted to amps, gives resistance.
Technical boundaries. The tool assumes a fixed LED forward drop and calculates power at the requested current, without recalculating it for the chosen part. Its standard-value rule rounds upward through a fixed list, then uses multiples of 100 ohms above that list.
LED Resistor Calculator
Choose a resistor that limits LED current for the supply and forward voltage. Check the power rating as well.
viewof led_vsupply = Inputs.range([1.8,12], {value:3.3,step:0.1,label:"Supply Voltage (V)"})viewof led_vf = Inputs.range([1.0,4.0], {value:2.0,step:0.1,label:"LED Forward Voltage V_f (V)"})viewof led_if_mA = Inputs.range([1,30], {value:20,step:1,label:"Desired LED Current (mA)"})
led_vdrop = led_vsupply - led_vfled_valid = led_vdrop >0led_r = led_valid ? led_vdrop / (led_if_mA /1000) :0led_power_mW = led_valid ? led_vdrop * led_if_mA :0led_standard =!led_valid ?0: led_r <=56?56: led_r <=68?68: led_r <=82?82: led_r <=100?100: led_r <=120?120: led_r <=150?150: led_r <=180?180: led_r <=220?220: led_r <=270?270: led_r <=330?330: led_r <=470?470: led_r <=560?560: led_r <=680?680: led_r <=1000?1000:Math.ceil(led_r /100) *100html`<div style="background: var(--bs-light, #f8f9fa); padding: 1rem; border-radius: 8px; border-left: 4px solid #E74C3C; margin-top: 0.5rem;">${led_valid ?html`<p><strong>Voltage Across Resistor:</strong> ${led_vsupply.toFixed(1)} - ${led_vf.toFixed(1)} = ${led_vdrop.toFixed(1)} V</p><p><strong>Calculated Resistor:</strong> R = ${led_vdrop.toFixed(1)} V / ${led_if_mA.toFixed(0)} mA = <strong>${led_r.toFixed(0)} Ω</strong></p><p><strong>Nearest Standard Value:</strong> ${led_standard} Ω</p><p><strong>Resistor Power Dissipation:</strong> ${led_power_mW.toFixed(1)} mW${led_power_mW >250?" -- Use 1/2W resistor!":""}</p>`:html`<p><strong>Supply voltage (${led_vsupply.toFixed(1)} V) must exceed LED forward voltage (${led_vf.toFixed(1)} V).</strong> Increase supply voltage or choose a different LED.</p>`}</div>`
Tip
Current-Limited LED Lab.
Try it yourself! Use the LED resistor calculator above to choose a safe resistor before connecting any real LED. This is the simplest place to see Ohm’s law prevent hardware damage.
1. Red LED at 5 V
Set supply = 5 V, LED forward voltage = 2 V, current = 20 mA. The answer should be about 150 Ω.
2. ESP32 at 3.3 V
Change supply to 3.3 V. The resistor gets much smaller because less voltage is left to drop.
3. Blue LED check
Try a 3 V blue LED on 3.3 V. Notice the small voltage margin and why brightness can be inconsistent.
Design question: which standard resistor value is safer when the calculated value falls between two real parts?
Note
Learning Points.
Observe:
Current Limiting: Resistor prevents excessive current that would destroy LED.
Ohm’s Law: R = (V_supply - V_LED) / I_desired.
Brightness: LED brightness proportional to current (up to max rating).
Power Dissipation: Resistor dissipates excess power as heat.
Resistor Calculation:
Start by With a 5 V supply, a red LED drop of about 2 V, and a 20 mA target current, the resistor needs to drop 3 V. Ohm’s Law gives 150 Ohm, and 150 Ohm or 220 Ohm are common safe choices. Finally With a 3.3 V ESP32 GPIO and the same red LED, the calculation gives about 65 Ohm. A 100 Ohm resistor is a common safer value because it lowers current and still leaves the LED visible.
Sensor Indicator Applications:
Status LEDs: Show sensor state (active, error, standby).
Threshold Indicators: Light up when sensor exceeds limit.
Multi-Color RGB: Different colors for different conditions.
Brightness Feedback: PWM LED brightness based on sensor reading.
Common Mistakes:
Without adequate current limiting, excessive current can damage the LED. A resistor that is too small can raise current and temperature, shortening life. Reverse polarity prevents normal operation and can damage an LED if its reverse rating is exceeded. Choose the resistor using the supply, LED and driver ratings; lifetime and brightness also depend on current and temperature.